pb rohs emsl22m2h-110.000m tr emsl22 m 2 h -110.000m tr series rohs compliant (pb-free) 2.5v 6 pad 3.2mm x 5mm plastic smd hcsl mems oscillator frequency tolerance/stability 50ppm maximum over -20c to +70c duty cycle 50 5(%) packaging options tape & reel nominal frequency 110.000mhz logic control / additional output output enable (oe) and complementary output electrical specifications nominal frequency 110.000mhz frequency tolerance/stability 50ppm maximum over -20c to +70c (inclusive of all conditions: calibration tolerance at 25c, frequency stability over the operating temperature range, supply voltage change, output load change, 1st year aging at 25c, reflow, shock, and vibration) aging at 25c 1ppm first year maximum supply voltage +2.5vdc 0.125vdc input current 65ma maximum (excluding load termination current) output voltage logic high (voh) 750mvdc typical, 600mvdc minimum output voltage logic low (vol) 25mvdc typical, 50mvdc maximum rise/fall time 300psec typical, 350psec maximum (measured over 20% to 80% of waveform) duty cycle 50 5(%) (measured at 50% of waveform) load drive capability 50 ohms to ground (output and complementary output) output logic type hcsl logic control / additional output output enable (oe) and complementary output output control input voltage vih of 70% of vcc minimum or no connect to enable output and complementary output, vil of 30% of vcc maximum to disable output and complementary output (high impedance) output enable current 60ma maximum (oe) without load period jitter (deterministic) 0.2psec typical period jitter (random) 2.0psec typical period jitter (rms) 1.5psec typical, 3.0psec maximum period jitter (pk-pk) 20psec typical, 25psec maximum period jitter (cycle to cycle) 10psec typical rms phase jitter (fj = 637khz to 10mhz; random) 1.6psec typical rms phase jitter (fj = 1.5mhz to 22mhz; random) 0.6psec typical rms phase jitter (fj = 1.875mhz to 20mhz; random) 0.5psec typical start up time 10msec maximum storage temperature range -55c to +125c environmental & mechanical specifications esd susceptibility mil-std-883, method 3015, class 2, hbm 2000v flammability ul94-v0 mechanical shock mil-std-883, method 2002, condition g, 30,000g moisture resistance mil-std-883, method 1004 moisture sensitivity level j-std-020, msl 1 resistance to soldering heat mil-std-202, method 210, condition k resistance to solvents mil-std-202, method 215 solderability mil-std-883, method 2003 (pads on bottom of package only) temperature cycling mil-std-883, method 1010, condition b thermal shock mil-std-883, method 1011, condition b vibration mil-std-883, method 2007, condition a, 20g www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 1 of 6
emsl22m2h-110.000m tr mechanical dimensions (all dimensions in millimeters) pin connection 1 output enable (oe) 2 no connect 3 case ground 4 output 5 complementary output 6 supply voltage line marking 1 xxxxx xxxxx=ecliptek manufacturing lot code 0.27 (x4) 0.80 (x2) 1.40 (x6) 1.00 (x6) www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 2 of 6 3.20 0.15 0.75 0.15 2.54 0.10 1.20 0.10 0.64 0.10 (x6) 1.27 typ (x4) 0.08 max 1.00 0.10 (x6) 5.00 0.15 3 2 1 4 5 6 all t oler ances are 0.1 sug g ested solder p ad la y out solder land (x6) all dimensions in millimeters
emsl22m2h-110.000m tr www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 3 of 6 output disable (high imped ance st a te) output w a veform & timing dia gram v oh v ol 80% 50% 20% f all time rise time t w t duty cycle (%) = t w /t x 100 v ih v il t plz t pzl clock outputs tri-st a te input q q output supply v oltage (v dd ) ground p o w er supply v oltage meter current meter 0.01 f (note 1) 0.1 f (note 1) note 1: an e xter nal 0.01 f cer amic b ypass capacitor in par allel with a 0.1 f high frequency cer amic b ypass capacitor close (less than 2mm) to the pac kage g round and supply v oltage pin is required. note 2: a lo w capacitance (<12pf), 10x atten uation f actor , high impedance (>10mohms), and high bandwidth (>500mhz) passiv e probe is recommended. note 3: t est circuit pcb tr aces need to be designed f or a char acter istic line impedance of 50 ohms . note 4: a 10 ohm to 33 ohm ser ies resistor is required to limit o v ershoot. r s v alue is circuit la y out dependant. p o w er supply switch complementar y output t r i-state t est cir cuit f or t ri-state and complementar y output 50 ohms oscilloscope f requency counter probe 2 (note 2) probe 1 (note 2) r s (note 4) no connect r s (note 4) 50 ohms
dia 50 min dia 20.2 min dia 13.0 0.2 2.5 min width 10.0 min depth t ape slot in core f or t ape star t dia 40 min access hole at slot location 1.5 min tape & reel dimensions *compliant to eia 481a emsl22m2h-110.000m tr 12.0 0.2 5.5 0.1 6.5 0.1 4.0 0.1 2.0 0.1 8.0 0.2 b0* dia 1.5 +0.1/-0 a0* 0.30 0.05 k0* 18.4 max 180 max quantity per reel: 1,000 units 12.4 +2.0/-0 www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 4 of 6
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods emsl22m2h-110.000m tr high temperature infrared/convection ts max to tl (ramp-up rate) 3c/second maximum preheat - temperature minimum (ts min) 150c - temperature typical (ts typ) 175c - temperature maximum (ts max) 200c - time (ts min) 60 - 180 seconds ramp-up rate (tl to tp) 3c/second maximum time maintained above: - temperature (tl) 217c - time (tl) 60 - 150 seconds peak temperature (tp) 260c maximum for 10 seconds maximum target peak temperature (tp target) 250c +0/-5c time within 5c of actual peak (tp) 20 - 40 seconds ramp-down rate 6c/second maximum time 25c to peak temperature (t) 8 minutes maximum moisture sensitivity level level 1 www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 5 of 6
t min s t max s critical zone t to t l p ramp-up ramp-down t l t p t 25 c to peak t preheat s t l t p temperature (t) time (t) recommended solder reflow methods emsl22m2h-110.000m tr low temperature infrared/convection 240c ts max to tl (ramp-up rate) 5c/second maximum preheat - temperature minimum (ts min) n/a - temperature typical (ts typ) 150c - temperature maximum (ts max) n/a - time (ts min) 60 - 120 seconds ramp-up rate (tl to tp) 5c/second maximum time maintained above: - temperature (tl) 150c - time (tl) 200 seconds maximum peak temperature (tp) 240c maximum target peak temperature (tp target) 240c maximum 1 time / 230c maximum 2 times time within 5c of actual peak (tp) 10 seconds maximum 2 times / 80 seconds maximum 1 time ramp-down rate 5c/second maximum time 25c to peak temperature (t) n/a moisture sensitivity level level 1 low temperature manual soldering 185c maximum for 10 seconds maximum, 2 times maximum. high temperature manual soldering 260c maximum for 5 seconds maximum, 2 times maximum. www.ecliptek.com | specification subject to change without notice | rev a 3/12/2011 | page 6 of 6
|
